Image Handler 2 (for ZC v1.3.8 ONLY) Support

[Serious]

We've discussing exactly that in the last half dozen or so posts.

Going to get busy re-installing IH2.

Back soon with results.

[RoPey]

Hi
I'm using ZenCart 1.3.7.1 for one of my customers (planning a full upgrade over the next month or so) and recently added Zen LightBox at their request. However, after that install the additional images ceased to display. I found that people said that Image Handler solves this issue, so installed Image Handler Version 2 for 1.3.7.

However, although the install works fine and I can see the additional images in the Admin area for IH, I still do not see the additional images on the products themselves.

I found on this thread http://www.zen-cart.com/forum/showth...35913&page=645 that apparently the order in which these two mods are installed makes a difference, but apparently the additional_images.php file is the key and the ZLB should be the one used. I've made sure that this is one being used but still see no additional images.

Can anyone tell me which bit of code actually controls the appearance of the additional images?

Thanks

[DarkAngel]

Hi
I'm using ZenCart 1.3.7.1 for one of my customers (planning a full upgrade over the next month or so) and recently added Zen LightBox at their request. However, after that install the additional images ceased to display. I found that people said that Image Handler solves this issue, so installed Image Handler Version 2 for 1.3.7.

However, although the install works fine and I can see the additional images in the Admin area for IH, I still do not see the additional images on the products themselves.

I found on this thread http://www.zen-cart.com/forum/showth...35913&page=645 that apparently the order in which these two mods are installed makes a difference, but apparently the additional_images.php file is the key and the ZLB should be the one used. I've made sure that this is one being used but still see no additional images.

Can anyone tell me which bit of code actually controls the appearance of the additional images?

Thanks

which version exactly are you using of IH2...the current one rev8d I thinks is for the newest cart software NOT that old of one.

not sure if it will work but I am positive someone will tell us for certain. (files were rewritten for the newer version of cart.

when I was running that version and lightbox I had to merge a couple of files to get it to work right

link to the store would help a lot as well as seeing what your settings are for ih2 from admin/configuration/images

[kaddie]

Hi Dark Angel,

Good to hear from ya! I did empty the cache from the new test site admin. Then I took a look at the bmz_cache folder on the new test site and the images are still there in the folders. Not all folders are there however. Some were emptied and removed. I did not re-upload the bmz_cache folder from the old test site because I am not sure what to do at this point.

I will email you about the old site in a few.

Thanks for helping.

[Serious]

Not sure what was wrong but after reloading IH2 it seems to be working, except the hover function.....[sigh].
www.seriousoffroadproducts.com

[DarkAngel]

Hi Dark Angel,

Good to hear from ya! I did empty the cache from the new test site admin. Then I took a look at the bmz_cache folder on the new test site and the images are still there in the folders. Not all folders are there however. Some were emptied and removed. I did not re-upload the bmz_cache folder from the old test site because I am not sure what to do at this point.

I will email you about the old site in a few.

Thanks for helping.

ok cause as for the bmz_cache folder just delete everything in there leaving only the .keep and .htaccess files there the IH2 will recreate all the image caches again.

I shall be waiting.

[DarkAngel]

Not sure what was wrong but after reloading IH2 it seems to be working, except the hover function.....[sigh].
www.seriousoffroadproducts.com

just went there and when i hover over the images i get the hover image---although it is the exact same size as what is showing.

if inded you do have the medium sized image to see it larger then look at your settings. there are several setting that MUST be alike for the pop up to work right

the following settings must match the Small Image Width and Small Image Height settings:

• Subcategory Image Width
• Subcategory Image Height
• Image - Product Listing Width
• Image - Product Listing Height
• Image - Product New Listing Width
• Image - Product New Listing Height
• Image - New Products Width
• Image - New Products Height
• Image - Featured Products Width
• Image - Featured Products Height
• Image - Product All Listing Width
• Image - Product All Listing Height

These settings are all updated in Admin > Configuration > Images.

now on mine I will admit the small image size has one size and I have no sub category images so that one is blank

as for the others they are according to the area...note that the small image is one size....the product info image is the intermediate size then the others match the small image size

[DivaVocals]

The latest versions of ZLB and IH2 are meant to work with the latest version of Zen Cart v1.3.9. I have NO IDEA if IH2 will work with Zen Cart 1.3.7.. I wish I could offer more help..My suggestion is to use a version of these modules which work with ZC v1.3.7..

Hi
I'm using ZenCart 1.3.7.1 for one of my customers (planning a full upgrade over the next month or so) and recently added Zen LightBox at their request. However, after that install the additional images ceased to display. I found that people said that Image Handler solves this issue, so installed Image Handler Version 2 for 1.3.7.

However, although the install works fine and I can see the additional images in the Admin area for IH, I still do not see the additional images on the products themselves.

I found on this thread http://www.zen-cart.com/forum/showth...35913&page=645 that apparently the order in which these two mods are installed makes a difference, but apparently the additional_images.php file is the key and the ZLB should be the one used. I've made sure that this is one being used but still see no additional images.

Can anyone tell me which bit of code actually controls the appearance of the additional images?

Thanks

[DivaVocals]

Not sure what was wrong but after reloading IH2 it seems to be working, except the hover function.....[sigh].
www.seriousoffroadproducts.com

Looks like you've got it all working now!!

[Serious]

Walked away from it for a few minutes.
Grabbed a beer.
Cursed at the CPU.


Everything started working.



Actually I just made a few minor changes in the Admin area and got it working.


So anyone need some parts for their rig?